pdnsd Homepage pdnsd FAQ Documentation GNU GPL (pdnsd's License) Download Section

pdnsd Documentation

This is the "official" pdnsd documentation and reference written by Thomas Moestl with revisions by Paul Rombouts.
It is up-to-date for version 1.1.8b1-par7. For older documentation, please refer to the doc directory of the respective pdnsd package.
A pdnsd HOWTO ("unofficial" step-by-step installation and setup instructions) is available at http://www.geocities.com/sunil_tt/.

0. Installation

0.1 Installing binary RPM's

To install a binary RPM, just do
This should install pretty much everything automatically. The only thing left for you to do is adapt your configuration file (stored in /etc/pdnsd.conf) according to your needs (see below). In the SuSE RPMs, a start script is also installed; read the section 0.4, Start at Boot Time about that.

0.2 Building RPM's

It is possible to build a binary RPM from a source package using the command
or alternatively from a tarball using the command
You can do this as root, but it is safer to build a binary package first as a normal user, and then, when all has gone well, install the resulting binary package as root as in the previous section. How to build an RPM package without being root is described at http://www-106.ibm.com/developerworks/library/l-rpm2/.

Several pdnsd-specific options are available when building RPM packages:
--with isdn Has the same effect as --enable-isdn (see below).
--without poll Has the same effect as --disable-poll (see below).
--with nptl Has the same effect as --with-thread-lib=nptl (see below).
--with underscores Has the same effect as --enable-underscores (see below).
--with ipv6 Has the same effect as --enable-ipv6 (see below).
--with tcpqueries Has the same effect as --enable-tcp-queries (see below).
--define "distro <distro>" Has the same effect as --with-distribution=<distro> (see below).
--define "run_as_user <user>" Has the same effect as --with-default-id=<user> (see below).
For RPMs the default <user> is "pdnsd".
--define "run_as_uid <uid>" If the user defined by the previous option does not exist when the RPM is installed, the pre-install script will try to create a new user with numerical id <uid>.
--define "cachedir <dir>" Has the same effect as --with-cachedir=<dir> (see below).
You can also configure which compiler flags will be used by setting the environment variable CFLAGS. Using a bash shell, you can do that on the command line like this:  CFLAGS="-O1 -Wall" rpmbuild ...
This is useful if you prefer a different level of optimization, for instance.

0.3 Installing from the pure sources (tar archives)

0.3.1 Decompressing

pdsnsd comes in two different packed archives: the standard gzip'ed version pdnsd-<version>.tar.gz, and the bzip2-packed version (about 10% smaller) pdnsd-<version>.tar.bz2. If you have bunzip2 installed on your computer, I recommed you save bandwidth and get the .bz2-version. To decompress it (using a modern tar) do
tar -xzf pdnsd-<version>.tar.gz
--or--
tar -xjf pdnsd-<version>.tar.bz2

If your tar doesn't do this, use:
gzip -dc pdnsd-<version>.tar.gz | tar -xf -
--or--
bzip2 -dc pdnsd-<version>.tar.bz2 | tar -xf -

0.3.2 Setup

Change into the pdnsd source directory and run configure. It takes the following command line options (if you do not specify an option, defaults will be used):
--prefix=dir Specify the prefix directory. The pdnsd files are installed in subdirectories of the prefix, the pdnsd and pdnsd-ctl executables are for example installed in the sbin subdirectory of the prefix. The default for this is /usr/local; you might want to set this to /usr (using --prefix=/usr).
--sysconfdir=dir Specify the config directory. pdnsd expects its pdnsd.conf file to reside there if the -c option is not given at startup. The default for this is the etc subdirectory of your prefix, e.g. /usr/local/etc if you did not specify a prefix. To set this e.g. to /etc, use --sysconfdir=/etc.
--with-distribution=distro Specify target distribution (default=Generic; others: RedHat, SuSE, Debian)
See below for the effect of these settings.
--with-target=platform Change compilation target platform (default: autodetect; others: Linux, BSD)
autodetect will attempt to detect whether you are using *BSD or Linux and should normally be sufficient. If this does not work, try specifyning you system manually.
--with-cachedir=dir Default directory for pdnsd cache (default=/var/cache/pdnsd)
This setting can be changed via config file settings when pdnsd was built.
--enable-isdn Enable ISDN support
This option will work only on Linux and may cause problems with 2.0.x or old 2.2.x kernels. You will need it for a proper if uptest under Linux for ISDN ppp devices.
--disable-ipv4 Disable IPv4 networking support (default=enabled)
--enable-ipv6 Enable IPv6 networking support.
If your OS does support IPv6 properly, you should be able to serve also IPv4 queries using this. Normally, this is disabled and you won't need it.
--disable-ipv4-startup Disable IPv4 on pdnsd startup by default (default=enabled)
--enable-ipv6-startup Enable IPV6 on pdnsd startup by default (default=IPv4). These options are only defaults, you can specify on the command line or in the config files which IP version will really be used. Normally, you won't need to change these.
--disable-udp-queries Disable udp as query method. You shouldn't need to change this.
--enable-tcp-queries Enable the TCP as query method. This is seldom needed in normal usage.
--with-query-method=qm Specify the query method (default=udponly, others: tcpudp, tcponly) If you have enabled both udp and tcp queries, this lets you control which query method pdnsd will use ny default. tcpudp will try tcp first and back out to udp if tcp is not supported by the server; udponly and tcponly should be clear.
--disable-tcp-server Disable tcp server. This may cause problems with very large answers.
--disable-src-addr-disc Disable the UDP source address discovery.
You need this only if you have trouble with messages saying "could not discover udp source address".
--disable-poll Disable poll(2) and use select(2) (default=enabled)
You will normally not need this.
--disable-new-rrs Disable new DNS RR types. This may cause problems with some resolvers. The new types are RP, AFSDB, X25, ISDN, RT, NSAP, PX, GPOS, AAAA, LOC, EID, NIMLOC, SRV, ATMA, NAPTR and KX. Most of these are seldomly needed, but AAAA is essential when using IPv6.
--enable-strict-rfc2181 Enforce strict RFC 2181 compliance.
This will cause pdnsd to reject DNS answers with incorrect timestamp settings (multiple RRs of the same type and for the same domain with different TTLs). Normally not needed.
--enable-underscores Allow underscores (_) in domain names. This breaks RFC compliance, but some sites use it for historical reasons because BIND used to support it.
--with-random-device=device Specify random device; default: C Library random() PRNG
pdnsd uses (pseudo-) random numbers as query IDs for security reasons (this makes forging DNS answers more difficult). This option controls where pdnsd gets these from. The default is the C library random() function, which is relatively weak. You can specify a device like /dev/urandom here if you like; pdnsd will read random numbers from it 16-bit-wise. /dev/urandom is present under Linux and most BSD derivates. You should not use /dev/random - it is more secure, but may block and delay pdnsd's answers for a long time.
You can specify arc4random to use the BSD arc4random() library function (default for FreeBSD target), which is considered safe.
You can also specify random as device to use the C Library random() function (described above).
--with-default-id=user Specify default user for pdnsd (default=nobody). This is the user that will be entered for the run_as option in the config file (see below) that will be installed during make install. You can change this any time in your config file.
--with-debug=level Specify debugging level. Debug output will only be generated if you turn on special switches; it might be useful for debugginh your config files, so I recommend using the default (9).
--with-verbosity=level Specify default message verbosity. The default should be ok.
--enable-rcsids Enable RCS IDs in executables (default=disabled).
For personal use, there is no need to do this. If you build rpm's, it might have advantages.
--enable-tcp-subseq Enable subsequent tcp queries. The DNS protocol standard requires that servers must be capable of answering multiple subsequent queries that are sent over the same tcp connection, and that the server may only close the connection by himself after a certain timeout. This feature is rarely used, but may make denial-of-service attacks easier, as it allows for an attacker to hold a connection open a long time (although the attacker's IP is most likely revealed then). For full standard compliance, you should use this option. If you do not use --enable-tcp-server, is option is not honored.
--with-tcp-qtimeout Specify default tcp query timeout after which the connection is closed if no full query has been received. The default is 30s. You can also change this option at run time using the tcp_qtimeout config file option. If you do not use --enable-tcp-server, is option is not honored.
--with-par-queries Specify the default number of queries that can be executed in parallel. You can also change this option at run time using the par_queries config file option. See the description of that option for an explanation of what it really does.
The default for this option is 2.
--with-thread-lib=<lib> Added by Paul Rombouts: Use this option if you experience problems with signal handling under Linux. The usual symptom is that pdnsd fails to save the cache to disk, and /var/cache/pdnsd/pdnsd.cache remains empty. If you experience this kind of trouble, try reconfiguring with different values for the --with-thread-lib option. The allowable values are linuxthreads (the default), linuxthreads2 (or lt2 for short), and nptl. I recommend that you first configure and compile without the --with-thread-lib option, then if you experience trouble try again with --with-thread-lib=lt2 and recompile. If your Linux system has an implementation of the Native POSIX Thread Library, which is the case with Red Hat 9 for instance, you should use --with-thread-lib=nptl .
Normally, you will need only --prefix, --sysconfdir and --with-distribution. If you specify your distribution using --with-distribution, this has the following effects: If you choose Generic, no rc script is installled, and a generic spec file is generated.
Further instructions are in the INSTALL document in the pdsd source directory. ./configure --help will give you a list of all supported command line options.

Note added by Paul Rombouts: Some people may want change the compiler optimization flag. I use the -O2 flag, but it might be safer to use a lower level of optimization or no optimization at all. In that case prefix the configure command with the desired compiler flags like this (assuming you're using a bash shell):

0.3.3 Building & installing

Type make in the source directory. Should work by now.
To install, type make install or do the installation by hand (see 0.3.4).
make install will do the following ($prefix is the prefix directory; see above):
  1. copies pdnsd to $(prefix)/sbin/
  2. copies pdnsd-ctl to $(prefix)/sbin/
  3. copies docs/pdnsd.conf.sample (a sample configuration) to the pdnsd config directory.
  4. creates your cache directory if it is not there. After installation, you should check the file permissions and create or edit /etc/pdnsd.conf to fit your needs (see below). If you use the run_as option, please make sure that your cache directory is owned by the user you specified with this option!
You must be root for this installation!
Security notes: never make the pdnsd cache directory writeable for untrusted users, or you will get several security holes: the users might modify the cache contents, or plant dangerous links.
If you use a pidfile, you should be aware that you introduce security problems if you place the pidfile in a directory in a NFS filesystem that is writeable for untrusted users. Generally, the pidfile directory (typically /var/run) should not be writeable for untrusted users.

0.3.4 Manual installation

For a manual installation, you need to do the following steps:
  1. Copy pdnsd and pdnsd-ctl from your build directory to an appropriate location (e.g. /usr/sbin).
  2. Copy docs/pdnsd.conf into the directory you want it to reside (/etc by default, and change it according to your needs (see below).
  3. Create your caching directory; default is /var/cache/pdnsd (you may change this in your pdnsd.conf); Permisions should be at max rwxr-xr-x (if you want to protect your cache and status socket, make it rwx------).
Thats it!

0.4 Start at boot time

In the rc folder of the pdnsd distribution are start scripts for pdnsd designed for different Linux distros. There are scripts for SuSE and Redhat Linux now.
The start scripts are automatically installed during RPM install, and also during make install if you specified your distro.

0.4.1 SuSE Linux startup

rc/SuSE/pdnsd is a start script for SuSE Linux. It was tested for 6.? but should run on some versions below. You can do make install as root in the rc/SuSE directory to install it, or you can install manually:
manual installation
For manual installation, copy rc/SuSE/pdnsd into /sbin/init.d/, go to /sbin/init.d/rc2.d/ and create there the following two symlinks:
S11pdnsd to ../pdnsd (do ln -s ../pdnsd S11pdnsd in that dir)
K34pdnsd to ../pdnsd (do ln -s ../pdnsd K34pdnsd in that dir)
The numbers dictate the order different services are started and might need to be modified. Then edit your /etc/rc.config file and add the line START_PDNSD=yes to start pdnsd at boot time.

If you used the make install command, START_PDNSD=yes has been appended to your /etc/rc.config file, causing pdnsd to be started at boot time. If you don't want that, change the yes into no.

This start script was created from /sbin/init.d/skeleton by me, so the most is copyrighted by SuSE. They put it under the GPL, however, so the license stated in COPYING also applies to this script. There is NO WARRANTY OF ANY KIND on these scripts. This is no official SuSE script, and SuSE naturally does NO support for it.

0.4.2 Red Hat Linux startup

rc/Redhat/pdnsd is a start script for Red Hat Linux. It was contibuted by Torben Janssen.
This was tested for 6.1 but should run on 5.0+. You can do make install as root in the rc/Redhat directory to install it, or you can install manually:
manual installation
For manual installation, copy rc/Redhat/pdnsd into /etc/rc.d/init.d/
Then go to /etc/rc.d/rc3.d and create there the following symlink:
S78pdnsd -> ../init.d/pdnsd (do ln -f -s ../init.d/pdnsd S78pdnsd in that dir)
Then go to /etc/rc.d/rc0.d and create there the following symlink:
K78pdnsd -> ../init.d/pdnsd (do ln -f -s ../init.d/pdnsd K78pdnsd in that dir)
Then go to /etc/rc.d/rc6.d and create there the following symlink:
K78pdnsd -> ../init.d/pdnsd (do ln -f -s ../init.d/pdnsd K78pdnsd in that dir)
This script is also covered by license stated in COPYING. Again, there is NO WARRANTY OF ANY KIND on these scripts. This is no offical Redhat script, and Redhat naturally does NO support for it

0.5 Notes for FreeBSD users

The special handling of ISDN ppp devices is only supported on Linux. It is not needed in FreeBSD, the normal device handling also works fine with isdn4bsd devices.
When compiled for FreeBSD, pdnsd as a small RFC compatability issue: RFC2181 demands answers on dns querys to be sent with the same source address the query packet went to. In seldom cases, this will not be the case, because the kernel selects the source address dependig on the interface that was used for sending the answer.
Setting the source address currently does not work for IPv4. I have written a kernel patch that will provide an easy way to program this. We'll see if or when it gets commited.


1 Invocation

When invoking pdnsd, you can specify various options at the command line. Command line options always override config file options. The various --noX options are present to override config file options.

pdnsd --help (or -h) gives you an overview of the pdnsd command line options.

pdnsd --version (or -V for short) prints licence and version information.

To start pdnsd as background daemon, specifiy --daemon (or -d for short) on the command line. Diagnostic and error messages after the actual daemon start will be printed to the syslog instead of the console. --nodaemon will disable this.

When starting pdnsd as a daemon, the -p option may be helpful: It writes the pid of the server process to the file of the name given as argument to this option.
Example: pdnsd -d -p /var/run/pdnsd.pid

If you want to specify a configuration file other that /etc/pdnsd.conf, specify -c or --config-file on the command line, followed by a filename.

If pdnsd was compiled with debugging options enabled, you may specify -g or --debug on the command line. This will cause extra diagnostic messages to be printed. When pdnsd runs in deamon mode, the messages will be written to the pdnsd.debug file in your cache directory. --nodebug disables debugging.

pdnsd -vn sets the verbosity level of pdnsd. n may be a digit from 0 to 3, where 0 means normal operation, while 3 will most verbose. Example is -v2

The option -s or --status enables the status control socket. This is a named socket in the cache directory called pdnsd.status. This socket allows run-time configuration of pdnsd using the utility pdnsd-ctl. See below for more details about pdnsd-ctl. --nostatus disables status control. See also the configuration option status_ctl in the global section.

The option -t or --notcp disables the seldom needed TCP server thread, which may save you some resources. --tcp will enable it.

Using the -m option, you can select the method pdnsd uses to query other name servers. Following methods are supported:
-muo: pdnsd will use UDP only. This is the fastest method, and should be supported by all name servers on the internt.
-mto: pdnsd will use TCP only. TCP queries usually take longer time than UDP queries, but are more secure against certain attacks, where an attacker tries to guess your query id and to send forged answers. TCP queries are not supported by some name servers.
-mtu: pdnsd will try to use TCP, and will fall back to UDP if its connection is refused.

2 The configuration file

This section describes the layout of the configuration file and the available configuration options. The default location of the file is /etc/pdnsd.conf. This may be changed with the -c command line option. An example pdnsd.conf comes with the pdnsd distribution in the docs directory and will be installed to /etc/ by make install.

2.1 Layout

The configuration file is divided into sections. Each section is prefixed with the section name and opening curlies ({) and closed with closing curlies (}). In each section, configuration options can be given in the form
option_name=option_value;
Option value may be a string literal (enclosed in "), a number or a constant. Constants are noted in the section description in <> signs, but are written in the file without these signs. Some options take more than one value; in this case, the values are separated with commas.
If you may supply one of a set of possible values to an option, this is noted in the documentation as
(option1|option2|option3|...)
Comments may be onclosed in /* and */, nested comments are possible. If the # sign or two slashes (//) appear in the configuration file, everything from these signs to the end of the current line is regarded as a comment and ignored.
There are examples for nearly all options in the sample config file.

2.1.1 global Section

The global section specifies parameters that affect the overall behaviour of the server. If you specify multiple global sections, the settings of those later in the file will overwrite the earlier given values.
These are the possible options:

perm_cache=(number|<off>);
Switch the disk cache off or supply a maximum cache size in kB. If the disk cache is switched off, 4 bytes will still be written to disk. The memory cache is always 10kB larger than the file cache. This value is 2048 (2 MB) by default.
cache_dir=string;
Set the directory you want to keep the cache in. The default is "/var/cache/pdnsd".
server_port=number;
Set the server port. This is especially useful when you want to start the server and are not root. Note that you may also not specify uptest=ping in the server section as non-root.
The default port is 53, the RFC-standard one. Note that you should only use non-standard ports when you only need clients on your machine to communicate with the server; others will probably fail if the try to contact the server on the basis of an NS record, since the A record that supplies the address for (among others) name servers does not have a port number specification.
server_ip=string;
Set the ip address pdnsd listens on for requests. This can be useful when the host has several interfaces and you want pdnsd not to listen on all interfaces. Addtionally, it is possibly to bind pdnsd to listen on 127.0.0.2 to allow pdnsd to be a forwarder for BIND. pdnsd will listen on all of your local interfaces by default. The ip is treated as string and therefore needs to have quotation marks around it.
linkdown_kluge=(<on>|<off>);
This option enables a kluge that some people might need: when all servers are marked down, with this option set the cache is not even used when a query is received, and a DNS error is returned in any case. The only exception from this is that local records (as specified in rr and source sections are still served normally. In general, you probably want to get cached entries even when the network is down, so this defaults to off.
max_ttl=number;
This options sets the maximum time a record is hold in cache in seconds. All dns resource records have a time to live field that says for what period of time the record may be cached before it needs to be requeried. If this is more than the value given with max_ttl, this time to live value is set to max_ttl. This is done to prevent records from being cached an inappropriate long period of time, because that is almost never a good thing to do. Default is 604800s (one week).
min_ttl=number;
This options sets the minimum time a record is hold in cache in seconds. All dns resource records have a time to live field that says for what period of time the record may be cached before it needs to be requeried. If this is less than the value given with min_ttl, this time to live value is set to min_ttl. Default is 120 seconds.
neg_ttl=number;
This option sets the time that negative cached records will remain valid in the cache if no time to live can be determined. This is always the case when whole domains are being cached negative, and additionally when record types are cached negative for a domain for which no SOA record is known to pdnsd. If a SOA is present, the ttl of the SOA is taken.
neg_rrs_pol=(<on>|<off>|<auth>);
This sets the RR set policy for negative cacheing; this tells pdnsd under which circumstances it should cache a record type negative for a certain domain. off will turn the negative cacheing of record types off, on will always add a negative cache entry when a name server did not return a record type we asked it for, and auth will only add such entries if the answer came from an authoritative name server for that domain. The preset is auth. This is normally the right thing, as some cacheing servers behave strange.
neg_domain_pol=(<on>|<off>|<auth>);
This is analogue to neg_rrs_pol for whole domain negative cacheing. The preset is on here, because I have not seen a cacheing server that will falsely claim that a domain does not exist. If you experience problems with false negatives, try setting this to auth.
run_as=string;
This option allows you to let pdnsd change its user and group id after operations that needed privileges have been done. This helps minimize security risks and is therefore recommended. The supplied string gives a user name whose user id and primary group id are taken.
A little more details: after reading the config file, becoming a daemon (if specified) and starting the server status thread, the main thread changes its gid and uid, as do all newly created threads thereafter. By taking another uid and gid, those threads run with the privileges of the specified user. Under Linux and FreeBSD, the server status thread runs with the original privileges only when the strict_setuid option is set to off (see below, on by default), because these may be needed for exec uptests. The manager thread also retains its original privileges in this case. You should take care that the user you specify has write permissions on your cache file and status pipe (if you need a status pipe). You should look out for error messages like "permission denied" and "operation not permitted" to discover permission problems.
strict_setuid=(<on>|<off>);
When used together with the run_as option, this option lets you specify that all threads of the program will run with the privileges of the run_as user. This provides higher security than the normal run_as option, but is not always possible. See the run_as option for further discussion.
This option is on by default.
Note that this option has no effect on Non-Linux systems.
paranoid=(<on>|<off>);
Normally, pdnsd queries all servers in recursive mode (i.e. instructs servers to query other servers themselves if possible, and to give back answers for domains that may not be in its authority), and accepts additional records with information for servers that are not in the authority of the queried server. This opens the possibility of so-called cache poisoning: a malicious attacker might set up a dns server that, when queried, returns forged additional records. This way, he might replace trusted servers with his own ones by making your dns server return bad IP addresses. This option protects you from cache poisoning by rejecting additional records that do not describe domains in the queried servers authority space and not doing recursive queries any more. An exception to this rule are the servers you specify in your config file, which are trusted.
The penalty is a possible performance decrease, in particular, more queries might be necessary for the same operation.
You should also notice that there may be other similar security problems, which are essentially problems of the DNS, i.e. any "traditional" server has them (the DNS security extensions solve these problems, but are not widely supported). One of this vulnerabilities is that an attacker may bombard you with forged answers in hopes that one may match a query you have done. If you have done such a query, one in 65536 forged packets will be succesful (i.e. an average packet count of 32768 is needed for that attack). pdnsd can use TCP for queries, which has a slightly higher overhead, but is much less vulnerable to such attacks on sane operating systems. Also, pdnsd chooses random query ids, so that an attacker cannot take a shortcut. If the attacker is able to listen to your network traffic, this attack is relatively easy, though.
This vulnerability is not pdnsd's fault, and is possible using any conventional name server (pdnsd is perhaps a little more secured against this type of attacks if you make it use TCP).
The paranoid option is off by default.
scheme_file=string;
In addition to normal uptests, you may specify that some servers shall only be queried when a certain pcmcia-cs scheme is active (only under linux). For that, pdnsd needs to know where the file resides that holds the pcmcia scheme information. Normally, this is either /var/lib/pcmcia/scheme or /var/state/pcmcia/scheme.
status_ctl=(<on>|<off>);
This has the same effect as the -s command line option: the status control is enabled when on is specified.
Added by Paul Rombouts: Note that pdnsd-ctl allows run-time configuration of pdnsd, even the IP addesses of the name servers can be changed. If you're not using pdnsd-ctl and you want maximum security, you should disable this option.
daemon=(<on>|<off>);
This has the same effect as the -d command line option: the daemon mode enabled when on is specified.
tcp_server=(<on>|<off>);
This has the same effect as the -t command line option: the tcp serving ability is enabled when on is specified.
pid_file=string;
This has the same effect as the -p command line option: you can specify a file that pdnsd will write its pid into when it starts in daemon mode.
verbosity=number;
This has the same effect as the -v command line option: you can set the verbosity of pdnsd's messages with it. The argument is a number between 0 (few messages) to 3 (most messages).
query_method=(<tcp_only>|<udp_only>|<tcp_udp>);
This has the same effect as the -m command line option. Read the documentation for the command line option on this. tcp_only corresponds to the to, udp_only to the uo and tcp_udp to the tu argument of the command line option.
run_ipv4=(<on>|<off>);
This has the same effect as the -4 command line option: if on is specified, IPv4 support is enabled, and IPv6 support is disabled (if available). ff off is specified, IPv4 will be disabled and IPv6 will be enabled. You can only use this option if you have compiled pdnsd with IPv4 as well as with IPv6 support.
debug=(<on>|<off>);
This has the same effect as the -g command line option: the debugging messages are enabled when on is specified.
ctl_perms=number;
This option allows you to set the file permissions that the pdnsd status control socket will have. These are the same as file permissions. The owner of the file will be the run_as user, or, if none is specified, the user who started pdnsd. If you want to specify the permissions in octal (as usual), don't forget the leading zero (0600 instead of 600!). To use the status control, write access is needed. The default is 0600 (only the owner may read or write).
Please note that the socket is kept in the cache directory, and that the cache directory permissions might also need to be adjusted. Please ensure that the cache directory is not writeable for untrusted users.
proc_limit=number;
With this option, you can set a limit on the pdnsd threads that will be active simultaneously. If this number is exceeded, queries are queued and may be delayed some time. See also the procq_limit option.
The default for this option are 20 query threads will be active (plus 3 to 6 threads that will always be present depending on your configuration).
procq_limit=number;
When the query thread limit is exceeded, connection attempts to pdnsd will be queued. With this option, you can set the maximum queue length. If this length is also exceeded, the incoming queries will be dropped. That means that tcp connections will be closed and udp queries will just be dropped, which will probably cause the querying resolver to wait for an answer until it times out.
See also the proc_limit option.
The default for this option is 30.
tcp_qtimeout=number;
This option sets a timeout for tcp queries. If no full query has been received on a tcp connection after that time has passed, the connection will be closed. The default is set using the --with-tcp-qtimeout option to configure.
par_queries=number;
This option sets the maximum number of queries that will be executed in parallel, i.e. how many servers are simultaneously queried. This may speed up the query process if there are very slow servers to be quered (the first answer we get will be taken), but it will also increase network and server load. 1 or 2 are good values for this option. The default is set using the --with-par-queries option to configure.
randomize_recs=(<on>|<off>);
If this option is turned on, pdnsd will randomly reorder the cached records of one type when creating an answer. This supports round-robin DNS schemes and increases fail safety for hosts with multiple IP addresses, so this is usually a good idea,
On by default.
query_port_start=number;
If given, defines the start of the port range used for queries of pdnsd. The value given must be >= 1024. The purpose of this option is to aid certain firewall configurations that are based on the source port. Please keep in mind that another application may bind a port in that range, so a stateful firewall using target port and/or process uid may be more effective. In case a query start port is given pdnsd uses this port as the first port of a specified port range (see query_port_end) used for queries. pdnsd will try to randomly select a free port from this range as local port for the query.
To ensure that there are enough ports for pdnsd to use, the range between query_port_start and query_port_end should be adjusted to at least (par_queries * proc_limit). A higher value is highly recommended, because other applications may also allocate ports in that range. If possible, this range should be kept out of the space that other applications usually use.
query_port_end=number;
Only used if query_port_start is given. Defines the last port of the range started by query_port_start used for querys by pdnsd. The default is 65535, which is also the maximum legal value for this option. For details see the description of query_port_start.

2.1.2 server Section

Each server section specifies a name server that pdnsd should try to get resource records or authoritative name server information from. The servers a queried in the order of their appearance (or parallel to a limited extend). If one fails, the next one is taken and so on.
You probably want to specify the dns server in your LAN, the caching dns server of your internet provider or even one of the root servers using server records.
The supported options in this section are:

ip=string;
Give the IP (the IP, not the hostname) of the server.
Multiple IP addresses can be given per server section. This can be done by entering multiple lines of the form ip=string; or a single line like this:
    ip=string,string,string;
IP addresses do not have to be specified in the configuration file. A server section without IP addresses will remain inactive until it is assigned one or more addresses with pdnsd-ctl, the pdnsd control utility.
port=number;
Give the port the remote name server listens on. Default is 53 (the official dns port)
uptest=(<ping>|<none>|<if>);
Determine the method to check whether the server is available. Currently defined methods are:
  • ping: Send an ICMP_ECHO request to the server. If it doesn't respond in timeout, it is regarded to be unavailable until the next probe.
  • none: The server is p.d. up
  • if: Check whether the interface (specified in the interface= option) is existent, up and running. This currently works for all "ordinary" network interfaces, interfaces that disappear when down (eg ppp?), and additionally for Linux isdn interfaces (as of kernel 2.2). Note that you need a /dev/isdninfo device file (major#45, minor#255), or the isdn uptest will always fail.
  • dev and diald: Perform an if uptest, and, if that was succesful, additionally check whether a program is running that has locked a given (modem-) device. The needed parameters are an interface (specified as for the if uptest, e.g. "ppp0") and a device relative to /dev (e.g. "modem" for /dev/modem specified using the device= option. pdnsd will then look for a pid file for the given interface in /var/lock (e.g. /var/run/ppp0.pid) and for a lockfile for the given device (e.g. /var/lock/LCK..modem), and then test whether the locking process is the process that created the pid file and this process is still alive. If this is the case, the normal if uptest is executed for the given interface.
    The dev option is for pppd dial-on-demand, diald is the same for diald users.
  • exec: Executes a given command in the /bin/sh shell (as /bin/sh -c <command>) and evaluates the result (the retur code of the last command) in the shell's way of handling return codes, i.e. 0 indicates success, all other indicate failure. The shell's process name will be uptest_sh. The command is given with the uptest_cmd option (see below). For secuity issues, also see that entry.

The default value is none.

NOTE: If you use demand dialling, use none, if or exec, since ping will send packets in the specified interval and the interface will thus frequently dial!

ping_timeout=number;
Sets the timeout for the ping test in tenth of seconds. The default is 600.
ping_ip=string;
The ip for the ping test. The default is the ip of the name server.
uptest_cmd=string,string;
or
uptest_cmd=string;
Sets the command for the uptest=exec function to the first string. If the second string is given, it specifies a user with whose user id and primary group id the command is executed.
This is especially useful if you are executing the server as root, but do not want the uptest to be performed with root privileges. In fact, you should never execute the uptest as root if you can help it.
If the server is running setuid or setgid, the privileges thus gained are attempted to be dropped even before changing identity to the specified user to prevent setuid/gid security holes (otherwise, any user might execute commands as root if you setuid the executable).
Note that this is not always possible, and that pdnsd should never be installed as setuid or setgid. The command is executed using /bin/sh, so you should be able to use shell builtin commands.
interval=number;
Sets the interval for the server-up-test in seconds. The default is 900; however, a test is forced when a query times out. The interval timeout is reset then.
If you specify onquery instead of a timeout, the interface will be tested before every query. This is to prevent automatically dialling interfaces (diald/pppd or ippp) to dial on dns queries. It is intended to be used in connection with a interface testing uptest ;-)
Note that using uptest=exec, you might run into performance problems on slow machines when you use that option. DON'T use this option with ping, as it may cause delays if the server does not answer (btw, it doesn't make sense anyway). Note also that using that option is no guarantee that the interface will not be used. When another (reachable) dns server tells pdnsd to query a third dns server for data, pdnsd will do that and has no means of checking whether this will dial up the interface or not. This however should be a rare configuration.
interface=string;
The network interface (or network device, eg "eth0") for the uptest=if option. Must be specified if uptest=if is given.
device=string;
The (modem-) device that is used for the dev uptest. If you use this for a dial-on-demand ppp uptest (together with uptest=dev), you need to enter the device you are using for your pppd here, e.g. modem for /dev/modem.
Must be specified if uptest=dev is given.
timeout=number;
Set the timeout for the dns query in seconds. The default is 120. You probably want to set this lower.
purge_cache=(<on>|<off>);
In every fetched dns record, there is a cache timeout given, which specifies how long the fetched data may be cached until it needs to be reloaded. If purge_cache is set to off, the cached records are not purged (unless the cache size would be exceeded, in this case the oldest records are purged). Instead, they are still served if they cannot succesfully be updated (eg. because all servers are down).
caching=(<on>|<off>);
Specifies if caching shall be performed for this server at all. Default is on.
lean_query=(<on>|<off>);
Specifies whether to use the "lean" query mode. In this mode, only the information actually queried from pdnsd is resolved and cached. This has the advantage that usually less cache space is used and the query is usually faster. In 90% of the cases, only address (A) records are needed anyway. If switched off, pdnsd will always cache all data about a host it can find and will specifically ask for all available records (well, at least it is a good approximation for what it really does ;-) This will of course increase the answer packet sizes.
Negative cacheing is only effective with lean_query activated.
Some buggy name servers may not deliver CNAME records when not asked for all records. I do not know if such servers are around, but if you have trouble resolving certain hostnames, try turning this option off.
A last note: If you use multiple pdnsd's that access each other, turning this option on is probably a big win.
This on by default.
scheme=string;
You can specify a pcmcia-cs scheme that is used in addition to the uptests. If you specify a scheme here, the server this section is for will only be queries if the given scheme is active. Shell wildcards (* and ?) are allowed in the string under their special meanings. You need to use the scheme_file option on the global section to make this option work.
preset=(<on>|<off>);
This allows you to specify the initial state of a server before any uptest is performed. on specifies that the server is regarded available. The default is on. This is especially useful when you set uptest=none; and want to control a server only via pdnsd-ctl.
proxy_only=(<on>|<off>);
When this option is set to on, answers given by the servers are always accepted, and no other servers (as, for example, specified in the NS records of the query domain) are queried. If you do not turn this option on, pdnsd will do such queries in some cases (in particular when processing ANY queries).
This option is useful when you do not want pdnsd to make connections to outside servers for some reasons (e.g. when a firewall is blocking such queries).
I recommend that you turn on lean_query when using this option.
Default is off.
policy=(<included>|<excluded>|<simple_only>|<fqdn_only>);
pdnsd supports inclusion/exclusion lists for server sections: with include= and exclude= (see below) you can specify domain names for which this server will be used or will not be used. The first match counts (i.e., the first include or exclude rule in a server section that matches a domain name is applied, and the search for other rules is terminated). If no rule matched a given domain name, the policy= option determines whether this server is used for the lookup for that domain name; when included is given, the server will be asked, and when excluded is given, it will not. If simple_only is given the server will be used if the name to lookup is a simple host name, on the other hand if fqdn_only is given the server will be used only for fully qualified domain names (i.e. the name has at least one dot in-between).
If no server is available for a queried domain, pdnsd will return an error message to the client that usually will stop the clients attempts to resolve a specific domain from this server (the libc resolver will e.g. return an error to the application that tried to resolve the domain if no other servers are available in the resolv.conf). This may be of use sometimes.
Note: the simple_only and fqdn_only constants were added by Paul Rombouts. They are useful for controlling which name servers (if any) will be used by pdnsd for simple host names.
The default for this option is included.
include=string;
This options adds an entry to the exclusion/inclusion list. If a domain matches the name given as string, the server is queried if this was the first matching rule (see also the entry for policy).
The domain name given must end in a dot. If it starts with a dot, the whole subdomain of the given name including the one of that name is matched, e.g. "foo.bar." will match the domain names a.foo.bar., a.b.c.foo.bar. and foo.bar.
If it does not start in a dot, only exactly the given name (ignoring the case, of course) will be matched (hint: if you want to include all subdomains, but not the domain of the given name itself, place an exact-match exclude rule before the include rule, e.g: exclude="foo.bar."; include=".foo.bar.";
exclude=string;
This options adds an entry to the exclusion/inclusion list. If a domain matches the name given as string, the server is not queried if this was the first matching rule (see also the entry for policy).
The domain name given must end in a dot. If it starts with a dot, the whole subdomain of the given name including the one of that name is matched, e.g. "foo.bar." will match the domain names a.foo.bar., a.b.c.foo.bar. and foo.bar.
If it does not start in a dot, only exactly the given name (ignoring the case, of course) will be matched (hint: if you want to exclude all subdomains, but not the domain of the given name itself, place an exact-match include rule before the exclude rule, e.g: include="foo.bar."; exclude=".foo.bar.";

2.1.3 rr Section

Every rr section specifies a dns resource record that is stored locally. It allows you to specify own dns records that are served by pdnsd in a limited way. Only PTR, A and SOA records are implemented.
This option is intended to allow you to define RRs for 1.0.0.127.in-addr.arpa. and localhost. (and perhaps even one or two hosts) without having to start an extra named if your cached name servers do not serve those records. It is NOT intended and not capable to work as a full-featured name server.

name=string;
Specifies the name of the resource records, i.e. the domain name of the resource the record describes. This option must be specified before any a, soa or ptr records. Only absolute domain names (names ending in the root domain, in dotted notation ending with a dot) are allowed. For this and all following arguments that take domain names, you need to specify domain names in dotted notation (example venera.isi.edu.). Do not forget the dot at the end!
owner=string;
Specifies the name of the host pdnsd runs on and that is specified in dns answers (specifically, nameserver records). Must be specified before any a, ptr and soa entries.
ttl=number;
Specifies the ttl (time to live) for all resource records in this section after this entry. This may be redefined. The default is 86400 seconds (=1 day).
authrec=(<on>|<off>);
If this is turned on, pdnsd will create authoritative local records for this rr section. This means that pdnsd flags the domain record so that records of this domain that are not present in the cache are treated as non-existent, i.e. no other servers are queried for that record type, and an response containing none of those records is returned. This is most time what people want: if you add an A record for a host, and it has no AAAA record (and no IPv6 address), you normally don't want other name servers to be queried for it.
This is on by default.
Please note that this only has an effect if it precedes the name and owner options!
a=string;
Defines an A (host address) record. The argument is an IP in dotted notation. pdnsd will serve this adrress for the hostname given in the name option.
ptr=string;
Defines a PTR (domain name pointer) record. The argument is a host name in dotted notation (see name). The ptr record is for resolving adresses into names. For example, if you want to have the adress 127.0.0.1 into localhost, and localhost into 127.0.0.1, you need something like the following sections:
rr {
owner="localhost.";
name="localhost.";
a="127.0.0.1";
soa="localhost.","root.localhost.",42,86400,900,86400,86400;
}
rr {
owner="localhost.";
name="1.0.0.127.in-addr.arpa.";
ptr="localhost.";
soa="localhost.","root.localhost.",42,86400,900,86400,86400;
}
The second section is for reverse resolving and uses the ptr option. There is something special about the name in the second section: when a resolver wants to get a hostname from an internet address, it composes an adress that is build of the IP address in reverse byte order (1.0.0.127 instead of 127.0.0.1) where each byte of the adress written as number constitutes a sub-domain under the domain in-addr.arpa.
So, if you want to compose an adress for reverse resolving, take your ip in dotted notation (eg 1.2.3.4), reverse the byte order (4.3.2.1) and append in-addr.arpa. (4.3.2.1.in-addr.arpa.) Then, define an rr section giving this address as name and the domain name corresponding to that ip in the ptr option.
soa=string,string,number,number,number,number,number;
This defines a soa (record source information) record. The first string is the domain name of the server and should be equal to the name you specified as owner.
The second string specifies the email address of the maintainer of the name server. It is also specified as a domain name, so you will have to replace the @ sign in the name with a dot (.) to get the name you have to specify here. The next parameter (the first number) is the serial number of the record. You should increment this number if you change the record.
The 4th parameter (the 2nd number) is the refresh timeout. It specifies after what amount of time a caching server should attempt to refresh the cached record.
The 5th parameter specifies a time after which a caching server should attempt to refresh the record after a refresh failure.
The 6th parameter defines the timeout after which a cached record expires if it has not been refreshed.
The 7th parameter is the ttl that is specified in every rr and should be the same as given with the ttl option (if you do not specify a ttl, use the default 86400)
All time parameters must be specified in seconds.

2.1.4 neg Section

Every neg section specifies a dns resource record or a dns domainthat should be cached negative locally. Queries for negatively cached records are always answered immediatley with an error or an empty answer without querying other hosts as long as the record is valid. The record remains valid until it is explicitely invalidated or deleted by the user using pdnsd-ctl.
This is useful if a certian application asks periodically for nonexisting hosts or RR types and you do not want a query to go out every time the cached record has timed out. Example: Netscape Communicator will ask for the servers news and mail on startup if unconfigured. If you do not have a dns search list for your network, you can inhibit outgoing queries for these by specifying
neg {
name="news.";
types=domain;
}
neg {
name="mail.";
types=domain;
}
in your config file. If you have a search list, you have to repeat that for any entry in your search list in addition to the entries given above!

name=string;
Specifies the name of the domain for which negative cache entries are created. This option must be specified before the types option. Only absolute domain names (names ending in the root domain, in dotted notation ending with a dot) are allowed. You need to specify domain names in dotted notation (example venera.isi.edu.). Do not forget the dot at the end!
ttl=number;
Specifies the ttl (time to live) for all resource records in this section after this entry. This may be redefined. The default is 86400 seconds (=1 day).
types=(<domain>|rr_type[,rr_type[,rr_type[,...]]]);
Specifies what is to be cached negative: domain will cache the whole domain negatively; alternatively, you can specify a comma-separated list of RR types which are to be cached negatively. You may specify multiple types options, but domain and the RR types are mutually exclusive.
The RR types are specified using their official names from the RFC's in capitals, e.g. A, CNAME, NS, PTR, MX, AAAA, ...
The command pdnsd-ctl list-rrtypes will give you a complete list of those types. pdnsd-ctl is build along with pdnsd and will be installed in the same directory as the pdnsd binary during make install.

2.1.5 source Section

Every source section allows you to let pdnsd read the records from a file in an /etc/hosts-like format. pdnsd will generate records to resolve the entries address from its host name and vice versa for every entry in the file. This is normally easier than defining an rr for every of your addresses, since localhost and your other FQDNs are normally given in /etc/hosts.
The accepted format is as follows: The #-sign initiates a comment, the rest of the line from the first occurence of this character on is ignored. Empty lines are tolerated.
The first entry on a line (predeceded by an arbitrary number of tabs and spaces) is the IP in dotted notation, the second entry on one line (separated by the first by an arbitrary number of tabs and spaces) is the FQDN (fully qualified domain name) for that ip. The rest of the line is ignored (in the original /etc/hosts, it may contain information not needed by pdnsd).

owner=string;
Specifies the name of the host pdnsd runs on and that are specified in dns answers (specifically, nameserver records). Must be specified before any file entries.
Only absolute domain names (names ending in the root domain, in dotted notation ending with a dot) are allowed. Example: venera.isi.edu.
ttl=number;
Specifies the ttl (time to live) for all resource records in this section after this entry. This may be redefined. The default is 86400 seconds (=1 day).
file=string;
The string specifies a file name. For every file entry in a source section, pdnsd will try to load the given file as described above. Failure is indicated only when the file cannot be opened, malformed entries will be ignored.
serve_aliases=(<on>|<off>);
If this is turned on pdnsd will serve the aliases given in a hosts-style file. These are the third entry in a line of a hosts-style file, which usually give a "short name" for the host. This may be used to support broken clients without a proper domain-search option. If no aliases are given in a line of the file, pdnsd behaves as without this option for this line.
This feature was suggested by Bert Frederiks.
It is off by default.
authrec=(<on>|<off>);
If this is turned on, pdnsd will create authoritative local records with the data from the hosts file. Please see the description of the option of the same name in the rr section for a closer description of what this means. Please note that this only has an effect for files sourced with file options subsequent to this option.

3 pdnsd-ctl

pdnsd-ctl allows you to run-time configure pdnsd. To make this work, you have to start pdnsd with the -s option (or use the status_ctl option in the config file). You also should make sure that you have appropriate permissions on the control socket (use the ctl_perms option to make this sure) and of your pdnsd cache directory (pdnsd keeps it's socket there). Please make sure the pdnsd cache directory is not writeable for untrusted users!
pdnsd-ctl takes one optional command line argument, -c. It is used to specify the cache directory (and takes this as argument). The default for this settings is the pdnsd default cache directory (specified at compile time). The cache directory for pdnsd-ctl must be the same pdnsd uses!
The following table lists the command line options that pdnsd-ctl supports. The command must always be the first option, the options to the command must follow in the given order.
In the following table, keywords are in a normal font, while placeholders are in italics.
Alternatives are specified like (alt1|alt2|alt3).
Command Options Description
help print a command summary.
version print version info
server (index|label) (up|down|retest) [dns1,dns2,...] Set the status of the server with the given index or label (where the given label matches the one given with the label option in the respective server section in the config file) to up or down, or force a retest. The index is assigned in the order of definition in pdnsd.cache starting with 0. Use the status command to view the indices and labels. You can specify all instead of an index or label to perform the action for all servers registered with pdnsd. Example:
pdnsd-ctl server 0 retest
An optional third argument consisting of a list of IP addresses (separated by commas or spaces) can be given. This list will replace the previous list of addresses of name servers used by pdnsd in the specified section of the config file. For example in the /etc/ppp/ip-up script called by pppd you could place the following line:
pdnsd-ctl server isplabel up $DNS1,$DNS2
If spaces are used to separate addresses the list will have to be quoted. Spurious commas and spaces are ignored. The last argument may also be an empty string, in which case the existing IP addresses are removed and the corresponding server section becomes inactive.
record name (delete|invalidate) Delete or invalidate the record of the given domain name if it is in the cache. Invalidation means that the record is marked as timed out, and such is reloaded if possible (if purge_cache is set to on, it will be deleted in any case).
For local records (i.e., records that were given in the config file using a rr section, records read from a hosts-style file and records added using pdnsd-ctl), invalidation has no effect. Deletion will work, though. Example:
pdnsd-ctl record localhost. delete
source fn owner [ttl] [(on|off)] [noauth] Load a hosts-style file. Works like using the pdnsd source option. owner and ttl are used as in the source section. ttl has a default of 900 (it does not need to be specified). The next to last option corresponds to the serve_aliases option, and is off by default (i.e. if it is not specified). noauth is used to make the domains non-authoritative - please see the description of the authrec config file options for a description of what that means. fn is the filename. The file must be readable by pdnsd! Example:
pdnsd-ctl source /etc/hosts localhost. 900 off
add a addr name [ttl] [noauth] Add a record of the given type to the pdnsd cache, replacing existing records for the same name and type. The 2nd argument corresponds to the argument of the option in the rr section that is named like the first option: a is a record for hostname-to-address mapping, aaaa is the same thing for IPv6 addresses, and ptr is for address-to-hostname mapping. See the documentation for the rr section for more details. The ttl is optional, the default is 900 seconds. noauth is used to make the domains non-authoritative - please see the description of the authrec config file options for a description of what that means. If you want no other record than the newly added in the cache, do
pdnsdctl record name delete before adding records. This is also better when overwriting local records. Example:
pdnsd-ctl add a 127.0.0.1 localhost. 900
add aaaa addr name [ttl] [noauth]
add ptr host name [ttl] [noauth]
add cname host name [ttl] [noauth]
neg name [type] [ttl] Add a negative cached record to pdnsd's cache, replacing existing records for the same name and type. If no type is given, the whole domain is cached negative. For negative cached records, errors are immediately returned on a query, without querying other servers first. The ttl is optional, the default is 900 seconds.
You can get a list of all types you can pass to this command using pdnsd-ctl list-rrtypes. The type is treated case-sensitive! Example:
pdnsd-ctl neg foo.bar A 900
pdnsd-ctl neg foo.baz 900


4 contrib/

The contrib directory in the pdnsd distribution contains useful user-contributed scripts.
So far, there are scripts contributed by Marko Stolle and Paul Rombouts that make pdnsd usable in a DHCP setup. Please take a look into the README file in the contrib directory for further information.

5 Problems...

If you have problems with configuring or tunning pdnsd, be sure to read the FAQ. If this does not help you, pdnsd crashes or you find bugs, please mail me at tmoestl@gmx.net.
Note added by Paul Rombouts: I have revised the code and added a few new features. See README.par and the ChangeLog in the source directory (or /usr/share/doc/pdnsd-<version> if you have installed an RPM) for more details. If you have questions about my modifications, you can find my email address at the end of README.par.

5 Hacking

Here comes some information you might find useful for hacking on pdnsd.

6.1 Source files

Makefile.am, configure.in, acconfig.h autoconf/automake/autoheader scripts. Makefile.am's are in most subdirectories.
pdnsd.spec.in A template from which configure generates a spec file for building rpm's for various distributions.
version Contains only the program version string. Needed for several templates.
src/rc/* rc scripts for various linux distributions.
src/cacheing/* The pdnsd cache subsystem(s) as defined in src/cacheing/cache.h. There is the "traditional" pdnsd system in the subdirectory native. This system keeps the cache in memory and uses hash tables for accesses. Sourav K. Mandal is working on a system using gdbm.
src/pdnsd-ctl/* Contains the code for pdnsd-ctl, a program that allows to control pdnsd at run time.
src/conf-lex.l.in The lex/flex source file for the config file lexer. This is a template because there might be inserted "%option yylineno" for proper flex support.
src/conf-lex.l. This is automatically generated by configure from conf.l.templ. It may be overwritten in any make, so never modify this, but conf.l.templ instead!
src/conf-parse.y The yacc/bison source of the config file parser.
src/conff.c, src/conff.h The configuration handler functions and their prototypes. The parser is called from here.
src/consts.h Some constants used by lexer, parser, config file handler functions and in the server status thread, among others.
src/dns.c, src/dns.h Define dns message structures, constants, and some common dns data handlers. dns.h contains gcc-specific code (in praticular, "__attribute__((packed))").
src/dns_answer.c, src/dns_answer.h Define functions that answer incoming dns queries.
src/dns_query.c, src/dns_query.h Define functions to manage outgoing dns queries.
src/error.c, src/error.h Functions for error output to stderr or the syslog.
src/helpers.c, src/helpers.h Define miscellaneous helper functions.
src/icmp.c, src/icmp.h Define a function for performing a ping test. This contains OS-specific code.
src/main.c Contains main(), which holds the command line parser, performs initialisations and signal handling.
src/netdev.c, src/netdev.h Define functions for network device handling. OS-specific.
src/servers.c, src/servers.h Define functions for the server status thread that performs the periodical uptests.
src/status.c, src/status.h Define functions for the status control thread. This is pdnsd's interface to pdnsd-ctl.


Thomas Moestl

Last revised: 10 Sep 2003 by Paul Rombouts