2.1. Supported Hardware

Debian does not impose hardware requirements beyond the requirements of the Linux kernel and the GNU tool-sets. Therefore, any architecture or platform to which the Linux kernel, libc, gcc, etc. have been ported, and for which a Debian port exists, can run Debian. Please refer to the Ports pages at http://www.debian.org/ports/arm/ for more details on ARM architecture systems which have been tested with Debian.

Rather than attempting to describe all the different hardware configurations which are supported for ARM , this section contains general information and pointers to where additional information can be found.

2.1.1. Supported Architectures

Debian "sarge" supports eleven major architectures and several variations of each architecture known as 'flavors'.

Architecture Debian Designation Subarchitecture Flavor
Intel x86-based i386   vanilla
speakup
linux26
Motorola 680x0 m68k Atari atari
Amiga amiga
68k Macintosh mac
VME bvme6000
mvme147
mvme16x
DEC Alpha alpha   generic
jensen
nautilus
Sun SPARC sparc   sun4cdm
sun4u
ARM and StrongARM arm   netwinder
riscpc
shark
lart
IBM/Motorola PowerPC powerpc CHRP chrp
PowerMac powermac, new-powermac
PReP prep
APUS apus
HP PA-RISC hppa PA-RISC 1.1 32
PA-RISC 2.0 64
Intel ia64-based ia64    
MIPS (big endian) mips SGI Indy/I2 r4k-ip22
MIPS (little endian) mipsel DEC Decstation r4k-kn04
r3k-kn02
IBM S/390 s390   tape
vmrdr

This document covers installation for the ARM architecture. If you are looking for information on any of the other Debian-supported architectures take a look at the Debian-Ports pages.

2.1.2. CPU, Main Boards, and Video Support

Each distinct ARM architecture requires its own kernel, because of this the standard Debian distribution only supports installation on a number of the most common systems. The Debian userland however may be used by any ARM CPU including xscale.

Most ARM CPUs may be run in either endian mode, however almost every current system implementation uses little-endian mode. Debian currently only supports little-endian ARM systems.

The common supported systems are

Netwinder

This is actually the name for the group of machines based upon the StrongARM 110 CPU and Intel 21285 Nothbridge it comprises machines are: Netwinder (possibly one of the most common ARM boxes), CATS (also known as the EB110ATX), EBSA 285 and Compaq personal server (cps, aka skiff).

Bast

This is a modern ARM 920 board with a 266MHz Samsung processor. It has integrated IDE, USB, Serial, Parallel, audio, video, flash and two ethernet ports. This system has a good bootloader which is also found on the CATS and Riscstation systems.

RiscPC

This machine is the oldest supported hardware it was released in 1994. It has RISC OS in ROM, Linux can be booted from that OS using linloader. The RiscPC has a modular CPU card and typicaly has a 30MHz 610, 40MHz 710 or 233MHz Strongarm 110 CPU fitted. The mainboard has integrated IDE, SVGA video, parallel port, single serial port, ps 2 keyboard and proprietay mouse port. The proprietary module expansion bus allows for up to eight expansion cards to be fitted depending on configuration, several of these modules have Linux drivers.

Riscstation

This is an inexpensive 56MHz 7500FE based machine with integrated video, IDE, PS2 keyboard and mouse and two serial ports. Its lack of processing power was made up for by its price. It may be found in two configurations one with RISC OS and one with a simple bootloader.

LART

This is a modular open hardware platform intended to be built be enthusiasts. To be useful to install Debian it requires its KSB expansion board.

2.1.3. Graphics Card

Debian's support for graphical interfaces is determined by the underlying support found in XFree86's X11 system. The newer AGP video slots are actually a modification on the PCI specification, and most AGP video cards work under XFree86. Details on supported graphics buses, cards, monitors, and pointing devices can be found at http://www.xfree86.org/. Debian "sarge" ships with XFree86 version 4.3.0.